How to Keep RV Sewer Hose from Freezing

0
74
rv sewer hose

“How to Keep RV Sewer Hose from Freezing”

In the winter, one of the biggest challenges of RVing is keeping liquids, liquids. And speaking of that, recreational vehicle owners also stress about their RV sewer hose that freezes. So the question is, “how to keep RV sewer hose from freezing.” Keep reading and learn a simple technique.

Read more: Best RV Sewer Hose – Top Best Sewer Hose for RV 2019

How to Keep the Sewer Hose from Freezing

One of the best ways to keep the sewer hose from freezing is insulation. Get its total length and find out how much insulation it needs.

You can layout the hose on the ground. However, make sure it’s flat and straight to ensure that you’ll get accurate measurements.

When done, you can use a tape measure to measure to get the accurate the hose’s actual measurement from end to end. Take note of the result. You will need it later.

[Are you using a new RV sewer hose? Check the label on the packaging to know how long the hose is.]

Measure only the sewer hose’s length connecting to the holding tank. When done, you should tape the heating cable every one foot along with your hose. The heating cable has the ability to detect the temperature of the sewer hose and then heats it up if it’s getting cold.

However, you must get one that matches your hose’s length. Using electrical tape, you must secure the sensor that must be pressed against your sewer hose.

Then, you should run the heating cable, and make sure it’s parallel with your hose. Next, start wrapping the electrical tape around the hose for every 30 centimeters to help it stay in place.

Where to buy heat cable? You can get it in specialty camping or hardware stores. This material is reliable if you’re RVing in the winter and staying in a place with over 32 degrees Fahrenheit.

Reminder – do not coil this cable around your hose because it might damage the hose due to too hot areas.

Covering the heat cable and hose with insulation tubes

Once you’ve secured that heat tube, use insulation tubes matching your hose’s length. Start pulling the side of the foam tubing in where to put the hose inside. Then, you can start pressing the opening in the tubing’s side together.

Doing so, you can prevent the hose from being exposed. And then, you can use duct tape for every one to two feet in order to keep the hose in place.

[Buy insulation from a hardware store. There are those with self-adhesive features that you don’t have to use tape.]

Wrap the foam’s outer part with insulation tape, which appears with a foil-like exterior. It can adhere itself in order to prevent the heat from escaping. You can then wrap the hose’s near end. But with each coil, you should overlap the tape by about ½ inch.

Keep wrapping the tape around your tubing right up to reaching the hose’s other end. Alternatively, you can use aluminum foil to wrap around your tubing, and then duct tape it for every 30 centimeters.

Keep the hose warm by plugging the heating cable into the power supply. Once it is plugged in, it will start working and detecting the low temperatures. It will also turn on automatically if the hose gets too cold.

There you have a simple way on how to keep RV sewer hose from freezing that you can consider if you want a better RV winter adventure. Do you have another tip on how to prevent your RV hose from freezing? Tell us in the comments.

In the winter, one of the biggest challenges of RVing is keeping liquids, liquids. And speaking of that, recreational vehicle owners also stress about their RV sewer hose that freezes. So the question is, “how to keep RV sewer hose from freezing.” Keep reading and learn a simple technique.

Read more: Best RV Sewer Hose – Top Best Sewer Hose for RV 2019

How to Keep the Sewer Hose from Freezing

One of the best ways to keep the sewer hose from freezing is insulation. Get its total length and find out how much insulation it needs.

You can layout the hose on the ground. However, make sure it’s flat and straight to ensure that you’ll get accurate measurements.

When done, you can use a tape measure to measure to get the accurate the hose’s actual measurement from end to end. Take note of the result. You will need it later.

[Are you using a new RV sewer hose? Check the label on the packaging to know how long the hose is.]

Measure only the sewer hose’s length connecting to the holding tank. When done, you should tape the heating cable every one foot along with your hose. The heating cable has the ability to detect the temperature of the sewer hose and then heats it up if it’s getting cold.

However, you must get one that matches your hose’s length. Using electrical tape, you must secure the sensor that must be pressed against your sewer hose.

Then, you should run the heating cable, and make sure it’s parallel with your hose. Next, start wrapping the electrical tape around the hose for every 30 centimeters to help it stay in place.

Where to buy heat cable? You can get it in specialty camping or hardware stores. This material is reliable if you’re RVing in the winter and staying in a place with over 32 degrees Fahrenheit.

Reminder – do not coil this cable around your hose because it might damage the hose due to too hot areas.

Covering the heat cable and hose with insulation tubes

Once you’ve secured that heat tube, use insulation tubes matching your hose’s length. Start pulling the side of the foam tubing in where to put the hose inside. Then, you can start pressing the opening in the tubing’s side together.

Doing so, you can prevent the hose from being exposed. And then, you can use duct tape for every one to two feet in order to keep the hose in place.

[Buy insulation from a hardware store. There are those with self-adhesive features that you don’t have to use tape.]

Wrap the foam’s outer part with insulation tape, which appears with a foil-like exterior. It can adhere itself in order to prevent the heat from escaping. You can then wrap the hose’s near end. But with each coil, you should overlap the tape by about ½ inch.

Keep wrapping the tape around your tubing right up to reaching the hose’s other end. Alternatively, you can use aluminum foil to wrap around your tubing, and then duct tape it for every 30 centimeters.

Keep the hose warm by plugging the heating cable into the power supply. Once it is plugged in, it will start working and detecting the low temperatures. It will also turn on automatically if the hose gets too cold.

There you have a simple way on how to keep RV sewer hose from freezing that you can consider if you want a better RV winter adventure. Do you have another tip on how to prevent your RV hose from freezing? Tell us in the comments.

 

LEAVE A REPLY

Please enter your comment!
Please enter your name here